Monthly Archives: June 2009

iRobot Roomba Isn’t What Anyone Expected


iRobot sent me a Roomba 560 robotic vacuum a month or two ago.  My family and I debated buying one a few times over the years they’ve been on the market, but who can justify spending $300+ on what amounts to a toy that obviously can’t clean floors?  It was fun to see the vacuum running around the floor in the stores vacuum department, but it was also pretty obvious that a robot that’s about a foot around and a couple of inches tall just can’t do a good job on the floor and we already had a couple of good, upright vacuums that could do the job for us — so we never bought one.

In March, we decided to have them on the show.  You can see the write-up on my show site here, and listen to the interview on my podcast site.  Matt Palma, the VP of Sales & Marketing over at iRobot, was pretty convincing.  We talked about some of the new technology embedded in the new 500 series of Roombas and it sounded impressive, but I’ve seen the Roombas before and since I wasn’t terribly impressed with them I knew that his talking points had been bravado.

Then the impossible happened.  They sent me one to try out.  And I tried it.  Things changed.

It took less than five minutes to get the Roomba set up.  We programmed it to start every morning at 8:30 and set up a couple of “Lighthouses” in rooms we wanted it to clean.  Then we hit the “Clean” button to send it on its way, and after playing a little tune on its internal speaker, off it went.

It uses a special pattern combined with numerous sensors to make passes on the floor and try and cover the problem areas, which is does quite effectivley.  It even monitors the stream of junk that it’s sucking in to see when it hits an area that deserves some additional attention, and will immediately go into an intense spot cleaning mode by spinning around and cleaning in some concentric circles.

The version we have, the 560, uses two brushes combined with the vacuum to do its job.  The first brush is a bristle brush not unlike those found in beater bars in regular vacuum cleaners, and the second is a four-bladed rubber brush that Roomba uses to clean tile, wood and conrete (non-carpeted) floors.  Actually they both run together in most, if not all, circumstances.

The results?  An excellent job of maintenance cleaning.  Roomba’s two trash compartments were full.  It had picked up everything from small pieces of paper and even sand all the way down to dust.  The pet hair that was on the carpet — even in corners — was gone, and the 560 isn’t even their pet hair model.

Then there’s the computer wires, power wires and tassels on the carpets.  We always have had to be careful when we’re vacuuming because the beater bars will rip up most of these wires.  Not a pretty picture.  I was concerned that the little Roomba would have some real trouble with all of these, so we spent some serious time cleaning before letting her go loose.

Of course, over the next few weeks, we stopped all of the preventative cleaning.  Wires were left laying around, the carpet tassels weren’t moved out of the way.  Things kind of got back to normal.  But how would Roomba do?

Amazingly enough, Roomba detects when it’s pulling on a wire, tassels or other obstructions and hasn’t damaged a single thing.  All of the wires have been left in-tact, all of the carpet materials are still in great shape an Roomba keeps going.

The robot takes about an hour and a half to clean our entire first floor, and it even remembers the layout of the room if it is started at the same point each time.  We use it’s “Spot” button when when take it to an area that needs cleaning and let it clean an approximately 3-foot square area, then we hit the “Dock” button and off it goes to find its dock and plugs its self in, recharges and is ready for the next vacuuming job.

My opinion of this little robot has come a long way since I first saw it cleaning a small spill at the retail vacuum store.  The Roomba is still not a complete replacement to getting out the big old vacuum and going to town, but it does do an absolutely acceptable job of keeping things fresh and clean, eliminating 6/7th of our vacuuming jobs as the old equipment (and out backs) get a break.

Good job, iRobot!

Reblog this post [with Zemanta]

We Gave Away a Porter Cable Lithium Combo Kit

Congratulations to Lisa A. from Manchester, NH for winning our 18V Lithium 4 Tool Combo Kit and thanks to Porter Cable for being on the show and providing the give-away!

Visit http://www.deltaportercable.com/Products/ProductDetail.aspx?ProductID=21238 to find out more about the tool kit.

This kit contains: A PCL180D Compact Drill/Driver, PCL186CS 6-1/2″ Circular Saw, PCL180RS Reciprocating Saw, and a PC180FL Pivoting Head Flashlight, as well as(1) PC18BLEX Extended Run Time Battery, (1) PC18BLX Compact Lithium Battery, PCLMVC Lithium Ion Fast Charger, (1) Double Ended Bit Tip, (1) 18T Carbide Tip Circ Saw Blade, (1) 6″ Wood Cutting Recip Blade, and Soft Sided Carrying Case.

The Technology and the Economy Show

We had a great show talking about the economy and technology:  How does one influence the other?
Last Saturday, with much of the economy hurting, we were talking about Productivity tools for home and business. How can we be more productive? How can we work from home and balance our lives.
Did you know that a recession can be a great time to start a company?  Many people are too worried about following their dreams when they’ve got a steady paycheck, but when the job’s gone it may be time to strike out on your own.  To that end, we even talked with some CEOs about how they started their companies!
Craig.
PS We’ll be announcing a free give-away contest on our Listener’s email list next week.  We’ve got about $1,500 worth of stuff to give away right now including an iRobot Roomba robotic vacuum cleaner , Brother P-touch electronic labeling systems , a CarMD diagnostic tool and much more!
PPS If you’re not a subscriber to my listener’s list, register here .  We will never rent or sell the list and we will never SPAM you.  You may unsubscribe at any time.

This Past Weekend’s Guests!

Segment 2
Guest: David Flynn
Title: CTO
Company: Fusion-io
Website: http://www.fusionio.com

Segment 3
Guest: Martyn Howgill
Title: Executive Director
Company: The Institute for Health Technology Studies (InHealth)
Website: http://www.inhealth.org/

Segment 4
Guest: Ed Moltzen
Title: Editor in Chief
Company: CRN Magazine Test Center
Website: http://www.crn.com/

Segment 5
Guest: Gerry McCartney
Title: VP IT and CIO
Company: Purdue University
Website: http://www.purdue.edu

Segment 6
Guest: Jenny Floren
Title: CEO
Company: Experience Inc.
Website: http://www.experience.com

Segment 7
Guest: Tom Pettibone
Title: Founder and Managing Partner
Company: Transition Partners
Website: http://www.tpco.us

Segment 8
Guest: Paul Jarman
Title: CEO
Company: InContact
Website: http;//www.incontact.com

Segment 9
Guest: Todd Thibodeaux
Title: CEO
Company: CompTIA
Website: http://www.comptia.org

Segment 10
Guest Name: Tony Fisher
Title: CEO
Company: Data Flux
Website: http://www.dataflux.com

Segment 11
Guest: Don Tapscott
Title: Author
Book: Grown Up Digital
Website: http://www.grownupdigital.com